![]() ![]()
Release the key and enter the 4digit Brandid (please refer to brand ID table guide) for the TV/AUX by pressing each digit key in sequence. To enable selection for AUX device, press key after hold > key for 3 secs, the TVmode led will give a Setup Confirmation blink. This enables the protocol and brand selection function for the TV device, the mode LED will remain on. #STANG ST 620 UNIVERSAL TV REMOTE INSTRUCTIONS FULL#Note that 9999 may result in a long setup (up to 15 minutes) * For the full list of TV brands, visit 6Ĩ Turn on the TV/Audio Press and hold the > key for 3 seconds until the setup LED lights up. #STANG ST 620 UNIVERSAL TV REMOTE INSTRUCTIONS MANUAL#Restart from the beginning 5ħ Shortlist of brands* Brands Name Bang & Olufsen BenQ Blue Sky Bush Carrefour Daewoo Firstline Funai Grundig Hitachi Insignia JVC Lg Loewe Metz Mivar Nokia Panasonic Philips Pioneer RCA Samsung Sanyo Sharp Sony Toshiba Vizio Brand Number If your brand is missing in this shortlist, look at the complete BRAND LIST at the end of the user manual Use '9999' as 4digit code in case you cannot find your brand in the BRAND LIST int the user manual. The red light under the TV button turns off. Press the TV button twice (2x) to finish setup Important: If you made a mistake: Press the TV button twice to exit setup. Note: You can also learn the butttons from your original remote. If those buttons are not working on your remote control, repeat step4. Try out the volume channel buttons on your remote. (This step normally takes between 5 and 60 seconds). Release the button immediately as soon as the TV switches off. 6) Enter the 4digit codes using the digit buttons. Look up the 4digit code for your brand in the adjacent shortlist of brands. Press and hold the TV button on your remote for 5 seconds. Protocol Keys STB protocol number 1 Home + Digit2 Humax (evision logo) 2 Home + Digit4 Airties 3 Home + Digit5 Kaon (Etisalat logo) 4 Home + Digit6 Kaon (evision logo) 5 Home + Digit 7 Huawei 6 Home + Digit 8 Pace 7 Home + Digit 9 Humax (Etisalat logo) 4Ħ Quick Start Guide to set up the remote of your TV * 1. If there is no reaction on the STB, repeat the previous steps, for each code listed below. Power on the STB and try out the dedicated STB buttons. The new STB protocol is now programmed to nonvolatile memory. SW Keys STB Model LED Confirmation 1 Digit2 Humax (evision logo) Two blinks 2 Digit4 Airties Four blinks 3 Digit5 Kaon (Etisalat logo) Five blinks 4 Digit6 Kaon (evision logo) Six blinks 5 Digit7 Huawei Seven blinks 6 Digit8 Pace Eight blinks 7 Digit9 Humax (Etisalat logo) Nine blinks 3ĥ The Set top box protocol can be changed in the field to retune the RCU to another STB using the following procedure: Press and hold key Home and the relevant digit key together for a minimum of 3 seconds, until the STB indicator LED blinks two times (of 500 ms each). 1 blink for Protocol 1, 2 blinks for Protocol 2, etc. The LED will blink, indicating that the Default STB Protocol has been programmed the number of blinks corresponds to the Protocol number selected, i.e. Refer to the table below for the protocol selection. Release the keys and press a key to select the Default Protocol. Key Description STB Mode (or no TV/AUDIO programmed) Menu Tools Next Previous Play/Pause Stop Power TV Forward Rewind REC List REC Back Guide Cursor Up OK Cursor Right Cursor Left Cursor Down VOD Vol +/ CH +/ Home Audio Numeric Keypad Subtitle Media Info TV/Radio Mute Color Function Keys Menu Tools Next Previous play/pause Stop Power Toggle Forward Rewind Rec List Record Back Guide Up OK Right Left Down VOD Vol+/or PT CH+/ TV/IRD Audio Numerics Subtitle Media Info TV/Radio Mute or PT Red Green Yellow Blue TV programmed only TV Power Toggle TV Source TV Vol+/ TV CH+/ TV>STB TV Mute TV/AUDIO Mode AUDIO programmed only TV+AUDIO programmed TV Power toggle AUX Power toggle TV Source TV Vol+ TV Mute TV Vol AUX Vol+/ AUX Vol+/ TV CH+/ TV>STB TV>STB AUX Mute AUX Mute AUX Source AUX Source AUX Power AUX Power 2Ĥ Universal Remote Control Programming for Etisalat Set Top Boxes The default Set Top Box protocol may be programmed in the field using the following procedure: Press the key, key and key simultanously for 3 sec, STB indicator LED will give a conformation blink and remain on. 1 UNIVERSAL REMOTE CONTROL INSTRUCTION MANUAL One for All SetTopBox TV Home Theaterģ No. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |